Most Powerful 10WATT Warm White LED 900-1000 Lumens
Powerful 10watt warm white LED requires 9V-12V forward voltage, 900mA forward current, and should be mounted to a heat sink for full output. LED output is 900-1000 Lumens, color temp is 3000K-3500K, and viewing angle is 120º.
Giant white LED Bar operates on 12VDC at 0.120Amps and puts out a bright cool white light from 4 powerful SMD LEDs. Each LED has a 0.61" dia X 0.24" thick diffusion lens on top. No heat sinking required as this bar has a copper bottom to dissipate heat. Has short flexible color coded leads for power. Size 12.4"L x 0.6"W. Nice for use in remote locations to power from solar panels such as garages, small storage rooms. Our G20540 solar panel actually powers this panel to full brilliance without overheating it in our full day long tests.
Our longest white LED light bar is 24 5/8" L. X 5/8" W. It operates on 24VDC at 0.170 Amp. Has 8 blinding white powerful SMD cool white LEDs. Each LED has a 0.63" Dia. X 0.22" diffusion lens on top. Has short flexible color coded leads attached. Worth many times our price!
This is an extremely bright and efficient compact light. It uses 2 rows of 4 (8 total) Samsung 120 degree viewing angle cool white SMD LEDs. This puts out a blinding 3500 degree white light. Size is about 1.75" x 2.25". This puts out the same amount of light and is the same size as our G20036, however, it is configured to operate on a 12VDC at 0.30Amps. Due to its unique copper base design, no heatsink is necessary. Please do not look directly at this from close distances.
Miniature precision made floppy drive motor. This has a 4 position connector but only 3 leads are used. The motor itself is about 0.78" diameter x 0.35" high with a 0.95" diameter lip. The entire outer assembly spins around a fixed inner shaft. It is very precise in construction. The inner shaft has a rigid 1.5" long mounting bracket. We have no idea how to make this motor spin, however they are new and should be easy to figure out. Each comes in a factory sealed bag -package of 10. Our reg. price $12.95 for 10 pieces.
The RF-520C-17410 motor operates from 9 to 15VDC and has good torque and efficiency. At 12VDC the speed unloaded is 5,500RPM, the current is 0.035Amp. At maximum efficiency (12VDC), the speed is 4,700RPM, current 0.18Amp, torque is 35g-cm and output is 1.51Watts - Stall torque is 220g-cm and current at stall 1.6Amp. Size is 1.29"Dia. x 1.09"L. Has 2mm diameter "D" shaft which is 0.3"L. Motor has two noise suppression mono capacitors already installed and flexible 4"L leads terminating in a two pin male connector. New.
We just got in these high quality miniature vibrator motors that are perfect for making bristle type robots. Size of body is only 0.36" long x 0.19" x 0.22" (excluding shaft). Shaft has "D" weight attached for vibration. Operates on 1.5VDC up to 3.5VDC. Resistance of motor is about 40 Ohms. Has two small terminals for battery hookup.
Fun and Educational Bubble Generator Science Kit introduces beginners to basic electronic circuit theory with the aid of 5 fun to build functional experiments. The experiments in the manual and completely re-usable and requires no soldering. The only items that are required are 2AA batteries and a bottle of bubble solution. Fun and educational summer activity for aspiring scientists!
This fun and educational SCI-TEC Rover comes with 10 activities/experiments. There is no soldering necessary for this exciting project. Parts simply snap together and wires are twisted onto connectors. Features a powerful motor with gear to propel your rover on almost any surface (including most carpets). Operates on 2 AA batteries (not included). Completed SCI-TEC Rover is about 9.5" long x 5" wide x 5" high. Learn about lamps, motors, circuits, and different types of propulsion! Complete with all parts and detailed instruction booklet. No Soldering Necessary.
The Rule IL280PG 12VDC at 4.5Amp inline submersible pump can deliver 280 gallons per hour of fresh or sea water at 14 psi. It is great for bilge pumping, showers, water delivery systems, pools, gardens, water transfer, etc. Head rate is 32ft, outlet hose bib for 0.5" internal diameter hoses, and size is 6.5" long x 1.5" diameter. Has a 3ft waterproof cable terminating in a special waterproof male 2 pin connector. Brand new -worth over $75. Reg. price $25.00.
Cool little pumps were made for auto windshield washing fluid. There are very compact-about 2.7" x 1.25" x 1.18". Had barb for a 1/4" diameter hose on the input and just a 9/32" hole for output (You can just glue a tip from a ball point pen or a small diameter tube if desired as the hole is about 0.2" deep) It works fine without a barb on the output anyway as the liquid just sprays out. Can pump air out of the output if you reverse the input voltage polarity. Runs on 9VDC up to 16VDC and requires about 0.8 to 1Amp of current. Has hallow tube on top with barb but we don't know what is was for. Brand New. Reg price 19.90.
Potter & Brumfield solid state relay type ELM1-1240S features low profile enclosed base and operates features load sense from 90 - 240VAC with pulsed output of 0.3A; 90 - 240VAC. Sorry no other information available. This is brand new and has 5 terminals.
Super heavy duty toggle switch mounts in a 0.5" hole in panel with supplied nut. Contacts are DPST rated 20 Amps at 125VAC. Size about 2.1" L. X 1.1" X 1.2" excluding bushing and chrome plated toggle. Has 4 screw terminals. Made by Carlingswitch.
Motorola MPSA42 high voltage transistor is rated 300V (collector to emitter VCEO) a 0.5A. In standard TO92 plastic case with full length leads already formed for easy use. New old stock. Sold in a package of 100.
Airpax 20Amp standard bolt-in type circuit breaker has black reset lever handle. Rated to 80VDC. Trip amps: 25. Size about 2.5" Tall X 0.74" Thick. Has optional switch rated 10Amps at 250VAC. Brand new—Retails for over $40.00.
Panel mounting standard size toggle switch has DPDT contacts rated 5Amp at 125VAC. Comes with panel mounting nut. Mounts in a 0.5" hole in panel. Size about 0.79" W. X 1.1" L. X 0.6" H. (excluding solder terminals, bushing and chrome bat toggle).
Handy 8-pin octal socket has screw on cover that covers the connecting pins for non chassis mounting applications. High quality and very handy when you need to connect an 8-pin relay, tube, device remotely. Standard 8-pin octal base.
Tiny neon glow lamp is rated for breakdown voltage 65AC/90DC. Circuit voltage 105 - 125V. These glow bright orange when connected to standard with a 100K resistor (not included). We also use these in triggering circuits for strobes and strobe capacitor ready lamps. Brand new. Size about 10mm Tall X 3.7mm Dia. Has 4mm long leads as shown. Sold in a package of 10.
Cherry type E53 snap action switch has SPDT contact rated 0.1Amp at 125VAC. This unique switch has a slotted rotating disk. It is designed to allow you to place a stiff wire into the slot to allow you to make a sensitive wire lever activated switch (wire not included). Size about 1.2" X 0.56" X 0.68" H, (excluding solder eyelets). Brand New!
Clarostat C0101193, 0603, 25K linear taper potentiometer is only 0.5" Sq. X 0.52". Has standard 0.62" L. X 0.25 Dia. shaft. Mounts in a 0.4" Dia. hole with included nut. Has 3.85" L. gold plated leads. Brand New—Retails for over $30.00
(Pkg of 5) Micro Switch Lever Action SPDT Switch V7-2B17P01
Micro switch lever action SPDT switch has contact rating of 4Amps at 125VA. Size of switch about 1.13" L. X 0.62" H. X 0.39" Thick. Lever is 0.97" L X 0.16" Wide. Brand new but may have slight tarnish on leads. Sold in a package of 5.
RCD-160, 5 watt power resistor is super high tolerance +/- 0.01% (not 1% but 0.1%). Rated 250 Ohm at 5 Watts. These are perfect for calibration of meters and instruments. Brand new—retails for much more. Marked RCD 160, 250 Ohm, 0.1%, H9736-1.
Meder/Standex BV50622 is an enclosed reed switch in a black housing about 1" X 0.24" with 2 lead cable 13" Long and 2-slot female connector. These are brand new and used in automatic washer board. The reed switch contained inside is SPST normally open contacts. The contacts close if a magnet is brought near the top or side of the housing.
Blinding 12 LED giant white LED bar is 28 5/8" L. X 13/16" W. It operates on 9VDC at 0.9Amp and produces an unbelievable amount of blinding cool white light. Consists of 12 powerful SMD LEDs. Each LED has a 0.61" Dia. X 0.24" Thick clear diffusion lens on top. No heat sinking required as this bar has a copper bottom to dissipate heat. Has short flexible color coded leads for power. Nice for use in remote locations to power from solar panels. Will even operate from a 9V battery for limited time (as it requires 1Amp current).
(Pkg of 5) Partial White LED Bar Assortment (as is)
Various cut off bars from LED strips. Each has at least 2 blinding white LEDs with clear diffusion lens. All LEDs are 100% good but you have to scrape paint off top to get to conductors and because these were cut from larger strips you might have to scrape paint off at certain spots—short a couple of foil traces together and then connect power to other traces to get the bar to light up. No instructions, however we have been able to light most bars by just tracing the foil paths. Anyway if you want to buy these at a cheap price and do a little experimenting this is a fabulous buy. Sold as is only—No information or hookup diagrams. Sold in a package of 5. Bars range from about 6" up to 12" (with various sizes and amount of LEDs). May vary from picture.
(Pkg of 2) Emerging Display EC16100TR LCD Display Module
Emerging Display single line 16 X 1 LCD module has 5 X 7 dot characters. We believe they are 5mm or 6mm character height. Overall size of module is 3.15 X 1.41 X 0.37”. Has one HD44780A00 IC on back and 16 gold plated pads on board for hookup. Brand new - sorry no data or hookup info. Sold in package of 2.
(Pkg of 2) Hitachi 16 X 2 LCD Display Module LM071
Hitachi LM071 is a 16 X 2 LCD module with 5 X 7 dot characters. Has 5mm character height. Size 3.15” X 1.41” X 0.37” overall. Has HD44100FS and HD44780A00 IC’s on back and 14 gold plated pads on board for hookup. Brand -sorry no data or hookup info. Sold in package of 2.
This giant man brilliant white crosswalk light panel can be seen from great distances outdoors. Panel size is 7" X 10 7/8”. Has 68 brilliant white LEDs and power supply that operates on 120VAC 60HZ. All you need to add is a line cord (not included). These were removed from crosswalks but all are 100% tested perfect. These are awesome displays and we connected 3 to our C4530 color organ with interesting brilliant unusual effects. Used - great condition.
Giant brand new super bright 8 1/2” X 12 1/2” LED light panel comes with 24VDC power supply made just for it. These were made for outdoor signs. Panel has 518 super bright clear lens white LEDs mounted on a white colored sturdy PC board. These are so bright that you can’t stare at them from close distances. Power supply is about 5.5” X 1.35” X 1.8”. It operates on 120VAC 60HZ and puts out 24VDC at up to 1.6 Amps. Requires line cord. Brand new
(Pkg of 20) Polyswitch (PTC) Resettable Fuse TRF600-150-2
Miniature resettable fuse features a trip current of 0.3Amp and a hold current of 0.15Amp. Made by Tyco this fuse is for circuits not exceeding 250V and 3Amps. Trip time is 4 seconds. Brand new on tape and reel with full length radial leads. Sold in a package of 20. Retails for $9.40.
SKIVING FINS, CPU cooler type E8DC/180 provides massive heat sinking plus 180 degrees, 12VDC ball bearing blower fan. Air flow is 9.39 cfm over copper fins. Dimension about 100 X 74 X 27.5mm. This supports AMD socket 754/939 and Opteron socket 940. Brand new is manufacture retail box. Retails for $39.95
(Pkg of 4) 6VDC Miniature DPDT Relay CDR752CGQPN-6DS
Miniature DPDT 6VDC relay is only 0.79”L X 0.38” W X 0.47” H. Contacts are rated 1Amp at 24VDC or 0.3Amp at 220VAC. Part# CDR752CQPN-6DS. Coil resistance is 235 Ohms. Has 8 pins on bottom. Sold in a package of 4 pieces.
Tiny bright digital 3 digit yellow voltmeter displays any voltage in the range of 2.6 to 30VDC when connected to its red & black leads. Requires about 30mA and is perfect for adding a voltmeter to a power supply, electronic battery operated devices, motorcycle etc. Size of display 10mm X 23mm. Overall size of unit 31mm X 12mm X 9mm thick. Brand new.
Potter & Brumfield 120VAC 1.8 to 180 Seconds Time Delay
Adjustable time delay relay by Potter & Brumfield model CKB - 38 - 71070. Has DPDT contacts rated 10Amp at 240VAC. Operates on 120VAC and has knob on top to adjust delay for relay release from 1.8 to 180 seconds. Size 1.74” X 2.37” X 2.81” excluding 11 pin base and knob. New but came to us in bulk so it may have a few cosmetic scratches on case.